What Is the Working of White Coal Machine!

 Coal is the major contributor to the human-made upsurge of carbon dioxide in the atmosphere in this fast-developing world. Its environmental influence spreads far across numerous zones, from water, air pollution, and waste management, up to the augmented land utilizes. Industries are seeking a new way to reduce the carbon footprint of production and manage their environmental effect in the face of greenhouse gas emissions. In this post, we will discuss bio-coal is a developing trend to substitute fossil coals in the industry.

Bio Coal Is A Tool For The Energy Transition:

According to a report, energy regarding emissions from the steel and iron industry presently amount to circa 2.3Gt CO2, accounting for nearly 7% of entire global productions from the energy system. Simultaneously, global steel production is forecasted to rise by approximately 30% until 2050 and intensively looking for measures to reduce its carbon footprint.

Nowadays, nearly 95% of the ore-based steel is shaped in blast furnaces, which are using coking coal as both the source of heat energy and the reduction agent. In the blast furnace, the iron oxide is decreased to metallic iron by fossil carbon resources such as coal, coke, and many more. The decreasing situations in the furnace are formed by top charged (coke) and tuyere-injected decreasing agents. Such furnaces generate emissions of nearly 2.3 tonnes of CO2 per tone of steel formed. Taking this carbon intensity, an important reduction of the CO2 footprint of steel production is required to meet the worldwide climate aims.

 

Designing The Bio Coal

Dissimilar kinds of bio coals are required for dissimilar metal manufacture procedures. Therefore, the initial point for the design is to distinguish precisely what industry requirements are for their procedure. Charging of self-reducing mixtures made of bio-coal and iron ore can partly change fossil carbon in the blast furnace. This tactic has the latent to lesser the current reserve zone temperature of the blast furnace appreciations to the through reduction of iron oxide in the agglomerates according to the research.

 The unintended decrease of FeO with CO at lesser temperature shifts towards the creation of more metallic iron at a precise limited pressure of CO. This also consequences in higher gas proficiency of reduction of the CO2 emission and the blast furnace. However, the volatile matter present in bio coal ought to contribute to the reduction and not be unconfined and lost with the blast furnace top gas to attain the supreme positive effect. A tailored made method towards the bio-coal parameters is significant to familiarize the market with a stable and quality product that achieves desired performance in the blast furnace due to these and other aspects.

 

The Bottom Line

Apart from this, if you are planning to make a white coal project, initially you have to research it and make a list of machines that are required for the project. Moreover, stay connected with us if you want to get a lot of information regarding the white coal project. 

 

Types and Benefits of Rotary Drum Dryer!

If you also have to gather a lot of waste material from your lawn on a daily basis, then you need to think about a rotary drum dryer. There are several types of dryers and a wide range of benefits. If still, you do not have a dryer, then maybe you are not aware of the advantages of a rotary dryer. Therefore, in this article, we will share the benefits of using a dryer and also discuss different types of dryers.

Tradition Processing Capabilities:

Numerous designs of the rotary dryer are incorporated and customizable options that can enhance processing efficiency. For instance, a rotary drum dryer has the ability to get the finest processing efficiency by designing around a material’s diverse characteristics and general objectives of the process. While processing, when the leftovers are under the procedure in the machine, then a wide range of material characteristics affect. You need to think about some chief waste material characteristics while designing a rotary dryer. And these features are waste material surface quality, material moisture level, material restrictions such as material size, and outlet substantial moisture target. 

 

Large Volume:

A rotary dryer has the capability to take any size of materials, process them, and produce quality products. It has the ability to occupy a greater footprint than other kinds of dryers and it means you can process a higher capacity of material in your dryer. It has an adequate storage capacity ranging from one ton per hour to more than 200 tons per hour of production. Though, it is required in the working atmosphere. 

 

Heavy-Duty Processing:

Rotary dryers provide a heavy-duty design and this is because are adaptive for heavy waste materials to process, such as those found in the mining industry. This is because waste materials are typically processed in a rotary dryer containing gypsum, potash, minerals, limestone, phosphates, and ores. If you keep your rotary dryer in a proper way, then your rotary dryer can sustain for a long time. 

 

Different Types Of Dryers:

Belt Dryer:

The second name of the Belt dryer is the conveyor dryer. In this dryer, the belt rotates to generate heated air. In that way, the wet feed move. When the inner layer of the feed makes contact with the wet feed, the heated air is produced. The best dryer can manage different sizes of particles. In the belt dryer, you can process sticky and sugary products. To reorient the feed and depiction interior surfaces to the heated air, some utilize several belts. 

 

Flash Dryers:

Flash dryers are used to dry the wet materials in different industries such as agri-food and chemical industries. By using heated air, it works on the principle of pneumatic transport. In flash dryers, the wet waste material is get passed through the special venture feeder that is present in the machine. Efficiently you can dry the wet goods or waste material in the flash dryers. It can accomplish the powders in a wide range of quantities and be able to handle some heat-sensitive materials due to its short holding time. But in the flash dryer, the heavy powder is hard to handle since it utilizes much air.

 

The Bottom Line:

Listed above are some types of dryers as well as the benefits of using them. You can pick a rotary drum dryer according to your requirements. So, make a list of your requirements which type of dryer you need to buy. Apart from this if you want to read about briquette machines, check our previous posts.  

Tips to Maintain Chipper Shredder!

 For a gardener, a wood chipper is an essential tool that reduces the workload. This large power tool helps to reduce the greater amount of debris in your lawn by disposing of and cleaning up. These chipper shredders are very helpful for cleaning branches, twigs, leaves, large piles, and logs that allow for cleaner, safer working areas. With the help of a wood chipper shredder, the debris can be recycled. After buying a wood chipper, most people are staying confused regarding the maintenance and using methods of a chipper shredder. So, let’s take a look at some tips that are discussed below:

Clear the area around you:

You have to remove all tripping hazards and obstructions around you and the chipper shredder. You need to keep the area clean and clear around the machine, free from instant motion, and unobstructed. Instantly, turn off the machine if you seem that something is stuck inside the machine. After that, check the machine and if found anything, then remove it from inside the machine. It can decrease the threat of falling and slipping around your wood chipper shredder tool.

 

Minimum speed first:

When you turn on your chipper shredder machine and start using it, you ought to run it at the lowest running speed. In addition, pay attention to the sound produced from the chipper shredder tool. There may be broken or loose components from the inside of the shredder machine. In this case, you need to turn off the machine instantaneously if you hear any odd sounds. Since this may be harmful to your machine. 

Lighten the load

Feeding the chipper shredder a wide range of debris can increase the risks of accidents, damage the system, and harm machine users. Just load leaves that fall within the limits of your wood chipper shredder machine. Moreover, feeding the leaves into the chipper in phases is one of the best options if the amount of leaves is high on your lawn.

 

Safe area:

Before starting the shredder machine, you should check whether the area around you is clear and free from animals or not. Make your mind up on a protection perimeter of the lowest amount of ten meters in all directions around the machine, and also be confident that the perimeter is marked with warning devices such as signs, cones, and barricades. If you see something or somebody coming towards you, instantly turn off the machine switch.

Check your power source:

It becomes essential for you to check your power sources. Assure that your machine is full of gas to function for a long time to complete your job if you make use of a gas power engine. And make sure that the cord doesn’t damage or crimp to work if you utilize electric power engineering.

Final words

After reading the above-written points, you must have known how you can maintain and use your wood chipper shredder. However, it becomes essential for you if you are a regular user of a chipper shredder. In the end, if you want to ask any question regarding the chipper shredder, drop a comment in the comment section; we will surely answer your questions.   

 

Basic Applications of Hammer Mill Grinder

 If you are looking for a hammer mill grinder, but you don't have sufficient knowledge about this machine, it becomes essential for you to know all about the hammer mill grinder before paying for it. Suppose you have purchased a hammer mill, but your basic requirements are not completing, then in this condition, all your money will waste. So, before buying the hammer mill grinder, you should know the primary applications of a hammer mill grinder so that you can choose the right kind of hammer mill grinder. Here are the basic applications of hammer mill grinder: 

 

Help to reduce the material size:

There is a need to decrease the sizes of products to fit the packaging equipment to package drugs or other products. The capsule filling machine that fills powder is a good example. A hammer mill grinder also helps decrease the size of the materials whose diameter is larger than the standard capsule sizes. Apart from this, hammer mill grinders can resize the dry materials, slurries, solids, fibrous materials, and many more.

 Help in cost-effective and faster recycling of substances:

Recycling is also an essential phase of any production procedure. This machine can resize, mill, and mix several ingredients of the final products. It gives a cost-effective and fast way to turn them into a useful end product. It is one of the best applications of a hammer mill grinder. However, you need reliable and high-quality equipment that conforms to all quality specifications and standards to benefit more from a hammer mill.  

Help to improve dissolution or formulation:

Mixing products need a large surface area in cosmetic, food processing, and pharmaceutical industries these days. In addition, small particles will make sure that there is an even distribution of particles in the final formulation. So, a hammer mill grinder will make sure consistency in producing a quality mixture and particle distribution. It is a vital aspect in the pharmaceutical industry where all the tablets and capsules should have an accurate dose quantity. 

Help to grind the legumes and other dry products:

In the pharmaceutical, cosmetic, and food processing industries, grinding is a significant producing process. These may consist of beans, soya, groundnuts, and many more. For example, hammer mills grind soya and coffee for making beverages in the food processing industries. In addition, in the cosmetic industry, where a wide range of nuts are grind to mate body creams and lotions, it is a common practice. 

Mix fibrous materials and solid dry:

A hammer mill grinder also helps to mix the fibrous materials and solid dry materials after grinding. It does the mixing simultaneously as this machine reduces the average size of materials. Consequently, whole ingredients are evenly distributed within the content in a final product with smaller particles. In addition, it eliminates the laborious procedure of making two distinct powders after grinding. 

 

Final words

Listed above are some of the basic applications of a hammer mill grinder. After reading the above-written points you can effortlessly decide for which purpose you need a hammer mill grinder. These applications of a hammer mill grinder are clear indications that this machine plays a significant role in several manufacturing procedures. At last, if you want to read briquette machines or other machines that are used in sense of recycling waste material, stay connected with us. In the future, we will publish articles based on your comments.

Tips for Using a Chipper Shredder

 

Often, people spend a lot of time gathering leaves from their gardens. Dealing with leaves every day is not an easy task if your garden is spread over a large area. With the help of a series of machines, leaves are removed from the garden and getting them to their final place. And using a chipper shredder makes that raw material into use. But, most people are unaware of using a chipper shredder. Therefore, to provide the knowledge regarding using a chipper shredder, here, we will share some tips that will really be helpful for you:

Clear the area

You need to remove all tripping hazards and obstructions near and about the chipper shredder. You should keep the area clean around the machine and free from immediate motion and unobstructed. Turn off the machine if you seem that something is stuck inside the machine. After that, check the machine and remove the thing that is stuck inside the machine. It can reduce the threat of falling and slipping around the machine.

Minimum speed first

When you start your chipper shredder and use it, you should run it at the lowest setting. Pay attention to the sound generating from the chipper shredder machine. There may be broken or loose parts of the machine inside and, you should switch off the machine instantly if you hear any strange sounds. Since this may be the cause of any damage to your machine. 

Lighten the load

Feeding the chipper shredder a large number of leaves can boost the odds of accidents happening, damaging the system and damaging individuals. Simply load leaves that fall within the limits of your chipper shredder. Apart from this, you can feed leaves into the chipper in phases if the amount of leaves is high on your lawn.

 

Zone of safety

Before starting the machine, make sure that the area around you is clear and free from animals. Make your mind up on a safety perimeter of a minimum of ten meters in all directions around the chipper shredder machine, and also be sure that the perimeter is marked with warning devices such as cones, signs, and barricades. If you see something or somebody coming towards you, switch off the machine instantly.

 

Inspect for use

Make it a point to analyze every component of the chipper shredder before use. If you find any visible signs of damage like fractures, worn hinges, and destroyed hood latches, don’t make use of the machine. Make sure that all bolts and screws are well fixed. Assess all devices and safety controls to verify that they are in a properly working state.

 

Wear proper clothes

It becomes essential to wear short-sleeved and tight-fitting clothing while working with a chipper shredder. Make sure that your pants and shirt are wrapped in and remove everything that might create obstacles in the machine-like belts, straps, jewelry, ties, and other dangling objects. During running a chipper shredder, standard safety gear involves safety goggles, a hard hat, heavy-duty cuff-free work gloves, steel-toed boots, and ear protection.

 

Final words

Listed above are some of the best tips that you should follow while using a chipper shredder. I hope, these tips will be helpful for you as a chipper shredder user. At last, if you have any questions regarding this article, leave a comment in the comment section; we will surely answer your questions. Also, know about How Machines Can Ease Your Pain

 

How Does A Briquette Machine Work – Types And Making Process

In the world of technology, there are many types of briquette machines available with different working principles. And they work on different pressures and temperatures for different materials.The briquette system can deal with all types of materials with appropriate size and moisture. Briquetting work always with the ring binder as it requires the binding effect to get sufficient power and strength for the completed briquette. In this blog, you will know all about the Briquette machine and its types with the working process. 

 What is a briquette machine?

It is a machine that turns waste material into hollow fuel briquette at high pressure. These briquettes are either charcoal or wooden blocks. This machine is used to convert the waste powder into a regular shape block, which can help to progress the situations for those powders.Both biomass and industrial waste are different from each other because of their binder source. 

 Types of briquette machines and how they work

Screw type

To press the raw material, a screw-type briquette machine is used with different materials and can be equipped with or without the heating system to output the briquette. The heating system is like a distinctive design for those briquettes that deal with materials that contain lignin. Screw type briquette machine is used with different materials to press the raw material. First of all, suitable materials are fed to the hopper and then converted by the screw inside the briquette. Material is taken from the fed port by rotating screw and compacts it against a die which assists the build-up of a pressure gradient along the screw.

Hydraulic type

A type of hydraulic work with a hydraulic station supplies great pressure. Almost all the materials can be briquette with this system because of its high pressure. Its working process is in the chamber where materials are fed into and materials are at high pressure. It affects their plasticity and makes them binding stably together as a block. 

 

Piston type

The piston-type briquette machine uses the rotary power of the mechanical device. And the piston drives the ram to return in the forming protective cover in order to generate a pressure forcing to form the material to briquette. A large pressure will be generated with the movement of the flywheel and punch the briquette in a short time. Materials raise their temperature to a high level and melt lignin with the action of these two types of heat. 

The Final word

This is all about briquetting machine and their whole procedure. After reading this blog, you will get an idea that how these machines working on different pressure and temperature. Hopefully, the information shared through this blog will be more helpful for you regarding the briquetting machine. Thanks! 

 

6 Common Problems In The Operation Of Briquette Machine

Briquette machine is used for making briquettes from waste materials and human beings can make use of these briquettes as fuel. However, there are a lot of benefits of briquetting machine such as it reduces the chances of pollution because instead of burning waste material, human beings can reuse them. But, during the operating of briquette machine some common problems occur that are described following:

 

It always makes noise:

The reason behind it is the water content and the temperature in the waste material are out of the normal range. And the only solution is drying waste material by the dryer to make sure that the materials are kept at proper humidity and temperature. The damaged components of the briquette machine are the reason of makes noise. So, you ought to replace them immediately.

 

It restarts frequently:

Replicate restart of the briquette machine is normally caused by the low power supply that can’t drive the machine to work usually. It would better suit the remedy to the case to solve this issue. Initially, the AVO meter detects the power supply voltage of the briquette machine. It is better detected under the situation that the machine is loaded so that to judge whether there is any power supply difficulty.

 

The oil pressure of briquette machine is inadequate:

There is inadequate oil pressure while the running procedure of the briquette machine. The reason is causing such a concern might be the deformation of the joint gasket and the blockage of oil suction. It ought to be washed and cleaned immediately to make sure the cleanness of briquette machine equipment if the oil suction is blocked. It ought to be replaced the deformed gasket with a new one if the joint gasket is deformed so that the machine can work efficiently and normally.

 

Water resistance of briquette machine:

The suspension installation way is adopted by a lot of users while the installation of the briquette machine. But there is still a gap between the bracket hinge and the briquette machine. It is snowing or raining, the water can leak into the machine that is the reason for the damage. Thus, the waterproofing measure ought to be adopted while installation. 

 

The deformation of completed products:

Occasionally, after shaped, the completed products are deformed by the entire procedure and the reason behind it is that the waste materials hold a large amount of water. It can reduce the water content in the waste materials to solve this issue. Through the dryer, the waste material can be dried. 

 

The briquette machine produces a large amount of dust:

The cyclone dust collector can be equipped as the corollary equipment if the machine generates a large amount of dust while the briquetting procedure. In the briquette machine, the dust collector has the benefit of enhancing the working efficiency greatly and cleaning the dust immediately. 

 

Final words:

The above-discussed points are described the common issues in the operation of the briquette machine. The improper operation may decrease the working efficiency of the briquette machine while generating the briquettes. If you like this informative blog, please share it with your contacts.

 

Working Principle And Features Of Sawdust Briquette Making Machine

A sawdust briquette machine is used to compress the waste material under high temperature and high pressure so that the briquette can be made from that compressed waste material. Initially, the large screws of the machine grind the waste material and convert it into briquettes. During the process, naturally, the lignin content is liberated under high temperature and pressure. In the briquetting process, the lignin works as the glue that is used to bind and compress the biomass to convert it into high-density briquettes. After that, the clean and green briquette is formed to use as fuel. Besides, here are the features of the sawdust making machine:

 

Long life and screw shaft:

The briquette machine made of durable material and the shaft is also made of durable material. When a screw shaft is manufactured with a milling machine, the distance between each screw and the angle of each screw is the same that never create a problem in the future. And the high hardness alloy steel is used to manufacture the screw shaft.

 

Long life of inner sleeve:

The duration of the inner sleeve using is one to two years. In the past, the whole steel bar is used to make the inner sleeve throughout the water jet cutting system so that the inner face gets smooth. So, it produced the briquettes easily and helps to save energy. That is the reason why the completed sawdust briquettes are smooth that you often feel by touching them. There are two components in the inner sleeve. And whenever one of them will damage, then you need to just change the major component.

 

Heating device and lubricating system:

Heating device: The sawdust briquette machine consists of two heat collars and the thick copper wires are used to make it and inside the machine a ceramic is present. Lubricating system: with the lubricating system, the gear box is also outfitted. Apart from this, by using an exhaust function, the briquette machine is designed, that assist to sustain consistent air pressure.  

 

Auto cutting system:

When a briquette is manufactured, then the prepared briquette is automatically cut in equal lengths, which is the great feature of a briquette machine. And briquettes can be easily stored in a warehouse.

 

Final words:

By reading the above-written points, you must have understood the working principle of the briquette machine and know about the features of the briquette making machine. If you want to read more about the briquette machine, drop a comment in the comment section. In the future, we will provide you more blogs related to sawdust machine.

 

How Machines Can Ease Your Pain

People in the olden days used to put a lot of effort into cutting down the woods and moving from place to place to sell them. Many people even lost their lives in doing this work. This work has stopped with the use of high technology machines. The working advanced specialization has discovered a lot of things in today's world. One of them is the White Coal project. Everyone knows how essential coal is today. So, this method can help us bring white coal in natural ways. This is obtained in the form of fuel with the help of chopped dried wood and burning it.

 Paddy Straw Grinder

The paddy straw is available in a wide range. These paddy straws are collected and released in some of the farms. These farms are difficult to handle and transport this amount of raw material and maintain them. The top working plants usually sit idle for weeks, taking the best care of the fields before it dries. Looking towards the way the processing system, the paddy straws are first compressed into tiny pellets and further using this output for refining it to powdered form which is further used for many useful things. The dust would contain a lot of secret energy in its size and weight and then transported for economical use.

 

The high and advanced upbringing to startup a Paddy straw grinder is designed for every desired capacity depending on the farmer's yields. The plan is to turn farmers with a fruitful profit on their farms or later selling to it nearby farms. To quick and surprise transport the paddy straws into nearby Biomass Plants is another clever challenge where farmers do not feel highly incentivized, and plenty of the paddy straws are burnt due to the distance of biomass plants from the farming area and transporting it is expensive.

 

Hammer mill

The best machine is used for slicing off the large pieces of wood into smaller ones in the required size. The Hammer mill is a large drum with a horizontal rotating shaft in it. The hammer is allowed to swing freely in the drum with center attachment. This size reduction technique is done in this metal container. It slices the whole content in just a few seconds. A small screen is fixed at the bottom of the machine, allowing the properly sized output to pass out.

Get your desired machines at Ecostan, the top leading company in these machines. Our experts take the best care while designing your special machine. Check out now!!

 

 

 

 

 

 

 

 

 

 

How to Improve The Biomass Briquette Quality

Biomass briquette is a type of renewable briquette which is much in demand in recent years and, there are many factors that can affect the biomass briquette quality. By using the useful tips given in this article, you will be able to improve biomass briquette quality. Numerous factors will influence the biomass briquette. There are divided into two parts. The first part is –internal part and the second part is the external part. Its internal part mainly contains raw material. While the external part includes the heating temperature, pressure, and the size of the raw material. If you want to know about tips on biomass briquette quality and the working process of Briquette Machine, this article is for you.

 

The heating temperature

The heating temperature has a great impact on the briquette density and strength. For the same raw materials with certain moisture, the necessary briquetting pressure will be lower in high temperatures. As you know, biomass briquette is typically a binder-free wat as we are the internal binder lignin. Around temperature 70 to 100 degrees Celsius, the lignin will become soft. When the temperature will rise, the binding affection will become better. The lignin starts melting when the temperature is reached at 160 degrees Celsius. And it turns into a gel that makes the binding effect much strong

 

The briquette pressure

In the biomass briquette making process, pressure is regarded as the most important factor. This briquette process is divided into three steps. The first step is soft briquetting-the second is transition briquetting, and stable briquetting. As the pressure is low in the first two steps and the density will increase quickly when the pressure is increased. While in the third step, the density will increase slowly along with the pressure.

 

The briquette and pressure keeping time

The pressure has its own effect on the quality of briquette when it`s small while it affects little when it`s big. It has been seen that the quality of affection can be ignored if the pressure-keeping time is more than 40 seconds. On the other side if the pressure keeping time is more than 20 seconds, an extra 10 seconds on pressure keeping the briquette density by 5%.

 

 

Raw material type

In different briquette methods, different kind of raw material is needed. Some raw material such as wood type, straw, etc. is good to briquette with the heating system. As the lignin create a well performance on the high temperature which highly enhancements the plasticity.

 

The moisture of the raw material

The density relaxation and burning effect of the biomass briquette are affected by moisture. Raw material with appropriate moisture will get an ideal briquette effect. Suitable moisture will help to pass pressure on the particle and a well lubricating. But the biomass that we get has moisture around 20-40%. The first part of the briquette energy will cost extra and useless moisture when briquette with high moisture. The raw material having low moisture is not suitable for lignin plasticization.

 

 

Crushed size of the raw material

The quality metrics of the biomass briquette are affected by crushed size-fall resistanceand density relaxation. When the raw material is introduced in a certain type of briquette machine, the size of the raw material must be smaller than the mould briquette output whole size. The raw material which is unsuitable in size, especially different in size and shape and will make the briquette with crack. The raw material will affect the strength of the biomass briquette. When the raw material is big, it will decrease the effectiveness of the briquette machine and also upturn the power consumption.

 

The Final word

These days biomass briquette making has become more popular with the development of renewable energy. This is all about Biomass Briquette Machine and tips to improve biomass briquette quality. Biomass waste recycles plant helps to make a good profit and also protection for the world`s environment today and onwards. 

 

 

Guidance To Choose The Right Type Of Hammer Mill Grinder

If you want to purchase a hammer mill grinder and you don't have sufficient knowledge about this machine, it is necessary to know all about the hammer mill grinder before purchasing it. Because it can be risky for you in the future if you purchase a hammer mill without knowing about it. So, before buying the hammer mill grinder, you ought to have enough knowledge about it so that you can choose the right kind of hammer mill grinder. So, in this blog, we will guide you on how you can select the right type of hammer mill grinder:

 

Production capacity:

In general, when you go to the market to purchase a hammer mill, you will notice a nameplate and instructions of the capacity rating on the machine. So, you should be clear how much your requirement related to the production capacity of raw materials before purchasing the hammer mill grinder. If you choose the production capacity of the hammer mill more than your requirement, you need to spend more money on the hammer mill. So, purchase a hammer mill according to your requirement. 

 

About crushing the raw materials:

Before purchasing the hammer mill grinder, you should be clear in your mind that which raw materials you want to crush. So, if you want to crush grain feed, then you ought to pick a hammer mill with the feed hopper on the top. Besides, you can select the disc mills if you want to crush the bran and wheat cereals. Apart from this, you can purchase a tangential feeding hammer mill to crush dissimilar types of materials, such as crop straw and grains. 

 

Power of the hammer mill grinder:

When you go to the market to purchase a hammer mill, you will notice the rated power of the electric motor on a nameplate of a hammer mill grinder. The electric power will be in a certain range. If you want to grind different types of raw materials in a hammer mill grinder, you need a powerful hammer mill grinder that varies on different kinds of raw materials. Basically, if you are crushing the corns with a 1.2mm screen mesh, the output per kilowatt per hour should not be less than 48 kg. So, you should pay attention to this thing while purchasing the hammer mill grinder. 

 

How much noise and dust produce the hammer mill?

Several different types of indigenous hammer mill grinders are available in the market that produced high sound. When a hammer mill grinder produces dust in a large amount and generates noise, sometimes, you can’t work in that type of working environment. So, you ought to choose the hammer mill that produces less dust without generating high noise.

 

Final words

If you purchase a hammer mill grinder without collecting enough information, it can be risky for you in the future and maybe wastage of your money. So, you should pay attention to the above-written points during purchasing the hammer mill grinder that will help you to choose the right type of hammer mill grinder. Besides, if you want to read more about the hammer mill grinder, leave your comments in the comment section. 

Read More:-Making Of Sawdust From Wood Log

 

 

Tips for using chipper shredder

 

We spent a lot of time dealing with leaves since removing the leaves from the lawn and collecting them to getting their final resting place engages a series of machines. Most people using their lawn tractor to collect the leaves from the lawn and after that run them over to the chipper-shredder, run them through that, and then put them into the compost bin. Here are a few tips that in this article we will share with you that will helpful for you:

 

1. A little bit at a time

Chipper-shredders have a lot of safety features built into them, which is a great thing. Practically the merely methods that you can get yourself in trouble are sticking your hands into the machine, which is not an easy task to do, or not wearing an eye guard in case something comes flying out of it towards your eyes. But one sure approach to block the entire program up is to try to put surplus through it at one time. Nothing gets sucked through the hopper if you put too many leaves in the hopper at one point, so to clear it you either have to turn off the machine, start over or start poking around with a big stick and pull everything out. Better you immediately prevent any of it by putting in little amounts of material at one time. It meant that instead of removing the whole collection bag from the mower into the hopper, I would slowly pour it out. It will take a little more time but it is much faster than frequently stopping to clear the block.

 

2. Drier is better

Persons that are working on leaf collection project first thing in the morning when the leaves are still covered in dew so they get wet. They just put the material in the machine and after that the more probably the machine is to block and the smaller the amount they put in at one time required to be. When they figured it, then out things get smoothly, but ahead of further review, they have saved much time if they just wait for the sun to dry everything off before started putting material through the shredder. The same thing is applied to other garden waste materials. People also put through most of what they cut out of the garden. It is harder than other plant stuff that doesn’t drop to the bottom of the hopper easily as leaves, but some people get around that by doing some planned loading. Little bundles at a time are required.

 

3. Respect size limits

The most chipper shredder can crush branches up to 3 inches in diameter and it does a good job with it. In fact, more branches ought to put through it since it makes the best mulch. Human beings put a branch that is most likely only 1.5 to 2 inches in diameter in it and it eats it all up until it gets to a large knot, or perhaps where it has connected to another branch, which is larger than 3 inches and it blocked it up good. Of course, it means stopping the entire thing, ensuring that all the components are finished rotating, and after that going in there to pull it out, which is not an easy task.

 

Final words

These are the tips for using a chipper shredder that will helpful for you during grinding the stuff. If you want to know something more about chipper shredder machines, leave a comment in the comment section and tell us what you want to read in the upcoming blog or article. We will provide an article or blog that will cover your questions. 

 

Hammer Mill: Grinder

 

Hammer Mill: Grinder

 

Appropriate a selection of the operating guidelines for a hammer mill can maximize expertise and enhance the uniforms of the product obtained:

 

Material to be ground:

Raw materials act differently when they are grounded; the factors that have the greatest influence on milling properties are toughness and flexibility. A rise of moisture in the product disturbs these two specifications and step up them. Analytically, 1% of the increase in humidity means 7% of more power to achieve the same result.

 

With indistinguishable product moisture measure and continual machine settings, the following circumstantial bond can be accepted for grain:

Mixture ratio: 

Oats: Barley: Wheat: Corn 

1     : 2         : 3         : 4

 

Peripheral speed:

Each product has its own gilt-edge milling speed. With increasing tangential speed, the granulation becomes first-rate. However, power demands will rise, while the thorough-paced will decrease.

 

The below sum up these rates in m/sec:

 

Millet (baajara)                     48 m/sec

 

Maize (makka)                    52 m/sec

 

Wheat (gehoon)                 65 m/sec

 

Rye bran (raeechokar)     75 m/sec

 

Barley (jau)                        105 m/sec

 

Bran (chokar)                    110 m/sec

 

Sieves configuration:

The sieve hammer mills are frequently driven steel sheets of 2 - 3 mm.
Density, with holes whose diameter is customarily the same to or less than the diameter of the mass. Bulkier holes mean higher open area and accordingly increased a performance altogether, decreased particular power requirements, rough product, a shorter useful lifespan of the sieves. If pierce chrome is used, thicker sheet metal could be used for balance reasons. Even with else ways identical conditions in terms of the diameter of the perforations and the open sieve area, this opportunity can make the motion of the lesser medium through the sieve more difficult, hence: the interrupt the achievement would fall; the product would become excellent; the specific ability requirement would get bigger.

In sieves, the supervision of perforation is generally aligned with the more significant preference of linen. Backpedal perforation must be specifically requested

Boost your workflow with Ecostan HammerMill, check its Advanced Technology features as:

Hammer Mill Machinery with Cyclone:

Model No	Production	Required Power
HM 120	upto 7000 KG/HR	199.5 HP
HM 100	upto 5000 KG/HR	151 HP
HM 60	upto  3000 KG/HR	84 HP
HM 50	upto  2000 KG/HR	65 HP
HM 40	upto  1300 KG/HR	52.5 HP
HM 20	upto  600 KG/HR	28 HP
HM 10	upto  250 KG/HR	15 HP